Last active
November 9, 2022 17:54
-
-
Save ooliver1/e06d9a76124f562b4820218187f1b00b to your computer and use it in GitHub Desktop.
My config for the Ender 3 Pro (old) + BTT SKR E3 + E3D Hemera
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
# This file contains common pin mappings for the BIGTREETECH SKR mini | |
# E3 v1.2. To use this config, the firmware should be compiled for the | |
# STM32F103 with a "28KiB bootloader" and USB communication. Also, | |
# select "Enable extra low-level configuration options" and configure | |
# "GPIO pins to set at micro-controller startup" to "!PC13". | |
# The "make flash" command does not work on the SKR mini E3. Instead, | |
# after running "make", copy the generated "out/klipper.bin" file to a | |
# file named "firmware.bin" on an SD card and then restart the SKR | |
# mini E3 with that SD card. | |
# See docs/Config_Reference.md for a description of parameters. | |
# Note: This board has a design flaw in its thermistor circuits that | |
# cause inaccurate temperatures (most noticeable at low temperatures). | |
[stepper_x] | |
step_pin: PB13 | |
dir_pin: !PB12 | |
enable_pin: !PB14 | |
microsteps: 16 | |
rotation_distance: 40 | |
endstop_pin: ^PC0 | |
position_endstop: 0 | |
position_max: 235 | |
homing_speed: 50 | |
[tmc2209 stepper_x] | |
uart_pin: PB15 | |
run_current: 0.580 | |
stealthchop_threshold: 999999 | |
[stepper_y] | |
step_pin: PB10 | |
dir_pin: !PB2 | |
enable_pin: !PB11 | |
microsteps: 16 | |
rotation_distance: 40 | |
endstop_pin: ^PC1 | |
position_endstop: 0 | |
position_max: 235 | |
homing_speed: 50 | |
[tmc2209 stepper_y] | |
uart_pin: PC6 | |
run_current: 0.580 | |
stealthchop_threshold: 999999 | |
[stepper_z] | |
step_pin: PB0 | |
dir_pin: PC5 | |
enable_pin: !PB1 | |
microsteps: 16 | |
rotation_distance: 8 | |
endstop_pin: ^PC2 | |
position_endstop: 0.0 | |
position_max: 250 | |
[tmc2209 stepper_z] | |
uart_pin: PC10 | |
run_current: 0.580 | |
stealthchop_threshold: 999999 | |
[extruder] | |
step_pin: PB3 | |
dir_pin: !PB4 | |
enable_pin: !PD2 | |
microsteps: 16 | |
rotation_distance: 7.824 # hemera | |
nozzle_diameter: 0.400 | |
filament_diameter: 1.750 | |
heater_pin: PC8 | |
sensor_type: EPCOS 100K B57560G104F | |
sensor_pin: PA0 | |
control: pid | |
pid_Kp: 21.527 | |
pid_Ki: 1.063 | |
pid_Kd: 108.982 | |
min_temp: 0 | |
max_temp: 300 # hemera | |
[tmc2209 extruder] | |
uart_pin: PC11 | |
run_current: 0.650 | |
stealthchop_threshold: 999999 | |
[heater_bed] | |
heater_pin: PC9 | |
sensor_type: ATC Semitec 104GT-2 | |
sensor_pin: PC3 | |
control: pid | |
pid_Kp: 54.027 | |
pid_Ki: 0.770 | |
pid_Kd: 948.182 | |
min_temp: 0 | |
max_temp: 130 | |
[fan] | |
pin: PA8 | |
[mcu] | |
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_37FFD9055252343036650843-if00 # /dev/serial/by-id/* | |
[printer] | |
kinematics: cartesian | |
max_velocity: 300 | |
max_accel: 3000 | |
max_z_velocity: 5 | |
max_z_accel: 100 | |
[static_digital_output usb_pullup_enable] | |
pins: !PC13 | |
[board_pins] | |
aliases: | |
# EXP1 header | |
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>, | |
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V> | |
# See the sample-lcd.cfg file for definitions of common LCD displays. | |
[display] | |
lcd_type: st7920 | |
cs_pin: EXP1_7 | |
sclk_pin: EXP1_6 | |
sid_pin: EXP1_8 | |
encoder_pins: ^EXP1_5, ^EXP1_3 | |
click_pin: ^!EXP1_2 | |
#kill_pin: ^!EXP2_8 | |
[output_pin beeper] | |
pin: EXP1_1 | |
# See docs/Config_Reference.md for a description of parameters. | |
# Pin mappings for BL_T port | |
#[bltouch] | |
#sensor_pin: ^PB1 | |
#control_pin: PB0 | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment