1 00:00:00,000 --> 00:00:07,000 [BLANK_AUDIO]
2 00:00:07,000 --> 00:00:08,320 >> Thank you for flying up.
3 00:00:08,320 --> 00:00:09,720
1 00:00:00,000 --> 00:00:07,000 [BLANK_AUDIO]
2 00:00:07,000 --> 00:00:08,320 >> Thank you for flying up.
3 00:00:08,320 --> 00:00:09,720
15@#&NOTICE: PL011_UART_BASE: | |
NOTICE: Booting Trusted Firmware | |
NOTICE: BL1: v2.0(release):LOG-uniBIOS_Hi1620_V200R002C20SPC001B023-98-g599589b-dirty | |
NOTICE: BL1: Built : | |
...............................................................................................NOTICE: BL1: Booting BL2 | |
ERROR: Hello Bl2 | |
NOTICE: BL2: v2.0(release):LOG-uniBIOS_Hi1620_V200R002C20SPC001B023-98-g599589b-dirty | |
NOTICE: BL2: Built : | |
NOTICE: BL1: Booting BL31 | |
12345NOTICE: BL31: v2.0(release):LOG-uniBIOS_Hi1620_V200R002C20SPC001B023-98-g599589b-dirty |
Last login: Tue Mar 21 08:56:13 on ttys010 | |
yarshure@Hoover ~ % ssh dev@192.168.2.88 | |
Welcome to Ubuntu 22.10 (GNU/Linux 5.19.0-35-generic aarch64) | |
* Documentation: https://help.ubuntu.com | |
* Management: https://landscape.canonical.com | |
* Support: https://ubuntu.com/advantage | |
System information as of Wed Mar 22 04:41:50 AM UTC 2023 |
DRAM Init-V11-DDR4 | |
0abc1-4Gb-Done | |
Read margin-DL:0.3980/DH:0.3882 CK (min:0.30) | |
U-Boot 2013.07 (Feb 22 2019 - 14:35:28) | |
I2C: ready | |
DRAM: 496 MiB | |
Flash: Found SPI Chip Winbond W25Q256(0x1940) 3-RD 0-WR |
#include <stdio.h> | |
#include <linux/if_vlan.h> | |
#include <netinet/ether.h> | |
#include <stdlib.h> | |
#include <string.h> | |
#include <unistd.h> | |
#include <sys/socket.h> | |
#include <sys/mman.h> | |
#include <sys/ioctl.h> | |
#include <arpa/inet.h> |
root@localhost:~# lspci -vvv -s 0001:01:00.0 | |
0001:01:00.0 Network controller: Mellanox Technologies MT27500 Family [ConnectX-3] | |
Subsystem: Hewlett-Packard Company InfiniBand FDR/EN 10/40Gb Dual Port 544FLR-QSFP Adapter (Rev Cx) | |
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ | |
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
Latency: 0, Cache Line Size: 32 bytes | |
Interrupt: pin A routed to IRQ 120 | |
Region 0: Memory at a040000000 (64-bit, non-prefetchable) [size=1M] | |
Region 2: Memory at a400000000 (64-bit, prefetchable) [size=32M] | |
Expansion ROM at a040100000 [disabled] [size=1M] |
noname ~ % sudo cu -s 115200 -l /dev/cu.usbserial-1130 | |
Connected. | |
CFE for Foxconn Router R6300v2 version: v1.0.15 | |
Build Date: Fri May 24 13:47:09 CST 2013 | |
Init Arena | |
Init Devs. | |
Boot up from NAND flash... | |
Boot partition size = 262144(0x40000) |
func ipv4_StringToInt(_ value: String) -> UInt32? { | |
var addr = in_addr() | |
return inet_aton(value.cString(using: .ascii), &addr) != 0 | |
? UInt32(addr.s_addr) | |
: nil | |
} | |
func ipv4_IntToString(_ value: UInt32) -> String { | |
let addr = in_addr(s_addr: value) | |
return String(cString:inet_ntoa(addr)) |
image 0xbff547e0: bdev 0xbff5e4e0 type SCAB offset 0x2000 | |
image 0xbff76200: bdev 0xbff5e4e0 type ibot offset 0x4000 len 0x401f8 | |
image 0xbff76280: bdev 0xbff5e4e0 type dtre offset 0x46000 len 0x106b8 | |
image 0xbff76300: bdev 0xbff5e4e0 type logo offset 0x58000 len 0x52b8 | |
image 0xbff76380: bdev 0xbff5e4e0 type bat0 offset 0x5e000 len 0xb178 | |
image 0xbff76400: bdev 0xbff5e4e0 type bat1 offset 0x6a000 len 0x3cf8 | |
image 0xbff76480: bdev 0xbff5e4e0 type glyC offset 0x70000 len 0xff8 | |
image 0xbff76500: bdev 0xbff5e4e0 type chg0 offset 0x72000 len 0xbb8 | |
image 0xbff76560: bdev 0xbff5e4e0 type chg1 offset 0x74000 len 0x3638 | |
image 0xbff765c0: bdev 0xbff5e4e0 type glyP offset 0x78000 len 0xbb8 |