-
-
Save mikejr83/fa3bbd32c5b5d4217281881ceab9dfa5 to your computer and use it in GitHub Desktop.
G91 ;Relative positioning | |
G0 E-2 F2700 ;Retract a bit | |
G0 E-2 Z0.2 F2400 ;Retract and raise Z | |
G0 X5 Y5 F3000 ;Wipe out | |
G0 Z10 ;Raise Z more | |
G90 ;Absolute positionning | |
G0 Y310 ;Present print | |
M106 S0 ;Turn-off fan | |
M104 S0 T0 ;Turn-off hotend 1 | |
M104 S0 T1 ;Turn-off hotend 2 | |
M140 S0 ;Turn-off bed | |
G28X ; Home x-carriages | |
M605 S1 ; Reset to auto-park | |
M84 X Y E ;Disable all steppers but Z |
G91 ;Relative positioning | |
G0 E-2 F2700 ;Retract a bit | |
G0 E-2 Z0.2 F2400 ;Retract and raise Z | |
G0 X5 Y5 F3000 ;Wipe out | |
G0 Z10 ;Raise Z more | |
G90 ;Absolute positionning | |
{if current_extruder==0} | |
G0 X0 Y310 ;Present print | |
{else} | |
G0 X310 Y310 ;Present print | |
{endif} | |
M106 S0 ;Turn-off fan | |
M104 S0 T0 ;Turn-off hotend 1 | |
M104 S0 T1 ;Turn-off hotend 2 | |
M140 S0 ;Turn-off bed | |
G28X ; Home x-carriages | |
M84 X Y E ;Disable all steppers but Z |
; -- BEGIN - DUPLICATION MODE INITIALIZATION -- | |
M605 S1 ; AUTO-PARK MODE | |
T0 ; SET TOOL 0 | |
G28 ; HOME ALL AXIS | |
M605 S2 X155 ; SET DUPLICATION MODE AND NOZZLE OFFSET | |
G28 X ; HOME X AXIS | |
G1 X77.5 ; SET BOTH EXTRUDERS TO THE MIDDLE OF THEIR PRINT AREA | |
; -- END - DUPLICATION MODE INITIALIZATION | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature] ; Set Extruder temperature | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
; -- BEGIN - MIRROR MODE INITIALIZATION -- | |
M605 S1 | |
T0 | |
G28 | |
M605 S2 X155 | |
G28 X | |
G1 X77.5 | |
M605 S3 X155 | |
; -- END - MIRROR MODE INITIALIZATION | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature] ; Set Extruder temperature | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
M605S1 ; Set to auto-park | |
T[initial_tool] | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature_[initial_tool]] ; Set Extruder temperature | |
G28 ;Home | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature_[initial_tool]] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
; TOOL CHANGE ---START--- | |
T[next_extruder] | |
{if current_extruder != next_extruder} | |
M104 S175 T[current_extruder] | |
{endif} | |
{if layer_num==0} | |
M109 S[first_layer_temperature_[next_extruder]] T[next_extruder] ; Wait for Extruder temperature | |
{else} | |
M109 S[temperature_[next_extruder]] T[next_extruder] ; Wait for Extruder temperature | |
{endif} | |
; TOOL CHANGE ---END--- |
Do you happen to have the rest of your profile? Even this part is immensely useful, and I can spend the time comparing the Cura settings provided by JGMAKER to transfer them over to PrusaSlicer, but if you are willing to share the full profile I would greatly appreciate it.
My profiles for PrusaSlicer are here: https://github.com/gabr42/3D/tree/master/JGMaker%20Artist-D/PrusaSlicer
Thank you so much! I think that will help me get up and running quickly. I am going to try and tune some of them for PLA and PVA dissolvable support. I will come back and post my results here if I get a good combination.
@jpswensen We have a good set of guys running the artist over on our Discord: https://discord.gg/vJ6GxxKW "3D Misfits". Please come and ask any questions. We'll be glad to help you out.
@mikejr83 , I tried to join that group and it just gave a "Whoops. Unable to accept invite" error. I am wonder if the group has been closed?
Using Custom G-Codes in PrusaSlicer
For use with the Artist-D standard or pro
Each of the "files" above represents different custom g-code sections in PrusaSlicer. The three main files and their corresponding sections are:
PrusaSlicer-Start.gcode
- Start G-code - Used for "Auto-Park" IDEX mode. This g-code will put the printer into "Auto-Park" mode. This sets the printer up to print and takes into account if you're using multiple extruders during the print.PrusaSlicer-End.gcode
- End G-code - Used for presenting the print at the end and cooling down the bed and extruders.PrusaSlicer-ToolChange.gcode
- Tool change g-code - Used for switching between extruders during a multi-material print. This code is enhanced when using the community firmware for the Artist-D (only available on the standard edition)When setting up the printer in PrusaSlicer I created a base version of the printer and set it up with two extruders. You can then use g-code listed above. I then created two more versions of the printer. Each of these had the bed sized changed to 155mm on the X. This was for mirror and duplication mode.
Use
PrusaSlicer-StartMirror.gcode
to in the "Start G-code" section for this new printer and it will automatically set the printer to mirror the printed model. Create a third printer for duplication. UsePrusaSlicer-StartDuplication.gcode
to put the printer into duplication mode. For both of these printers the "End G-code" is the same. UsePrusaSlicer-End-Mirror-Duplication.gcode
to return the printer back to "Auto Park" IDEX mode.