Created
May 4, 2021 12:44
-
-
Save airtonzanon/85c7ebcb593189999fa510669496445f to your computer and use it in GitHub Desktop.
raspberry py boot files + Waveshare LCD 5 inch
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
dwc_otg.lpm_enable=0 console=serial0,115200 console=tty1 root=PARTUUID=334dade7-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo quiet init=/usr/lib/raspi-config/init_resize.sh splash plymouth.ignore-serial-consoles |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
# For more options and information see | |
# http://rpf.io/configtxt | |
# Some settings may impact device functionality. See link above for details | |
# uncomment if you get no picture on HDMI for a default "safe" mode | |
#hdmi_safe=1 | |
# uncomment this if your display has a black border of unused pixels visible | |
# and your display can output without overscan | |
#disable_overscan=1 | |
# uncomment the following to adjust overscan. Use positive numbers if console | |
# goes off screen, and negative if there is too much border | |
#overscan_left=16 | |
#overscan_right=16 | |
#overscan_top=16 | |
#overscan_bottom=16 | |
# uncomment to force a console size. By default it will be display's size minus | |
# overscan. | |
#framebuffer_width=1280 | |
#framebuffer_height=720 | |
# uncomment if hdmi display is not detected and composite is being output | |
#hdmi_force_hotplug=1 | |
# uncomment to force a specific HDMI mode (this will force VGA) | |
#hdmi_group=1 | |
#hdmi_mode=1 | |
# uncomment to force a HDMI mode rather than DVI. This can make audio work in | |
# DMT (computer monitor) modes | |
#hdmi_drive=2 | |
# uncomment to increase signal to HDMI, if you have interference, blanking, or | |
# no display | |
#config_hdmi_boost=4 | |
# uncomment for composite PAL | |
#sdtv_mode=2 | |
#uncomment to overclock the arm. 700 MHz is the default. | |
#arm_freq=800 | |
# Uncomment some or all of these to enable the optional hardware interfaces | |
#dtparam=i2c_arm=on | |
#dtparam=i2s=on | |
#dtparam=spi=on | |
# Uncomment this to enable infrared communication. | |
#dtoverlay=gpio-ir,gpio_pin=17 | |
#dtoverlay=gpio-ir-tx,gpio_pin=18 | |
# Additional overlays and parameters are documented /boot/overlays/README | |
# Enable audio (loads snd_bcm2835) | |
dtparam=audio=on | |
[pi4] | |
# Enable DRM VC4 V3D driver on top of the dispmanx display stack | |
dtoverlay=vc4-fkms-v3d | |
max_framebuffers=2 | |
[all] | |
#dtoverlay=vc4-fkms-v3d | |
hdmi_group=2 | |
hdmi_mode=1 | |
hdmi_mode=87 | |
hdmi_cvt 800 480 60 6 0 0 0 | |
dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900 | |
display_rotate=2 | |
hdmi_drive=1 | |
hdmi_force_hotplug=1 | |
#max_usb_current=1 | |
dtparam=i2c_arm=on | |
dtparam=spi=on | |
enable_uart=1 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment