Last active
August 29, 2015 14:27
-
-
Save NegishiTakumi/d76b0f3c04f5f97aa9ec to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| pi@raspberrypi ~ $ sudo cat /sys/kernel/debug/gpio | |
| GPIOs 0-53, bcm2708_gpio: | |
| gpio-17 (lirc_rpi ir/in ) in hi | |
| gpio-18 (lirc_rpi ir/out ) in lo | |
| gpio-47 (led0 ) out lo | |
| pi@raspberrypi ~ $ sudo cat /etc/modules | |
| # /etc/modules: kernel modules to load at boot time. | |
| # | |
| # This file contains the names of kernel modules that should be loaded | |
| # at boot time, one per line. Lines beginning with "#" are ignored. | |
| # Parameters can be specified after the module name. | |
| snd-bcm2835 | |
| lirc_dev | |
| lirc_rpi gpio_in_pin=17 gpio_out_pin=18 | |
| pi@raspberrypi ~ $ sudo cat /etc/lirc/hardware.conf | |
| # /etc/lirc/hardware.conf | |
| # | |
| # Arguments which will be used when launching lircd | |
| LIRCD_ARGS="--uinput" | |
| #Don't start lircmd even if there seems to be a good config file | |
| #START_LIRCMD=false | |
| #Don't start irexec, even if a good config file seems to exist. | |
| #START_IREXEC=false | |
| #Try to load appropriate kernel modules | |
| LOAD_MODULES=true | |
| # Run "lircd --driver=help" for a list of supported drivers. | |
| DRIVER="default" | |
| # usually /dev/lirc0 is the correct setting for systems using udev | |
| DEVICE="/dev/lirc0" | |
| MODULES="lirc_rpi" | |
| # Default configuration files for your hardware if any | |
| LIRCD_CONF="" | |
| LIRCMD_CONF="" | |
| pi@raspberrypi ~ $ sudo cat /boot/config.txt | |
| # For more options and information see | |
| # http://www.raspberrypi.org/documentation/configuration/config-txt.md | |
| # Some settings may impact device functionality. See link above for details | |
| # uncomment if you get no picture on HDMI for a default "safe" mode | |
| #hdmi_safe=1 | |
| # uncomment this if your display has a black border of unused pixels visible | |
| # and your display can output without overscan | |
| #disable_overscan=1 | |
| # uncomment the following to adjust overscan. Use positive numbers if console | |
| # goes off screen, and negative if there is too much border | |
| #overscan_left=16 | |
| #overscan_right=16 | |
| #overscan_top=16 | |
| #overscan_bottom=16 | |
| # uncomment to force a console size. By default it will be display's size minus | |
| # overscan. | |
| #framebuffer_width=1280 | |
| #framebuffer_height=720 | |
| # uncomment if hdmi display is not detected and composite is being output | |
| #hdmi_force_hotplug=1 | |
| # uncomment to force a specific HDMI mode (this will force VGA) | |
| #hdmi_group=1 | |
| #hdmi_mode=1 | |
| # uncomment to force a HDMI mode rather than DVI. This can make audio work in | |
| # DMT (computer monitor) modes | |
| #hdmi_drive=2 | |
| # uncomment to increase signal to HDMI, if you have interference, blanking, or | |
| # no display | |
| #config_hdmi_boost=4 | |
| # uncomment for composite PAL | |
| #sdtv_mode=2 | |
| #uncomment to overclock the arm. 700 MHz is the default. | |
| #arm_freq=800 | |
| # Uncomment some or all of these to enable the optional hardware interfaces | |
| #dtparam=i2c_arm=on | |
| #dtparam=i2s=on | |
| #dtparam=spi=on | |
| # Uncomment this to enable the lirc-rpi module | |
| dtoverlay=lirc-rpi,gpio_in_pin=17,gpio_out_pin=18 | |
| # Additional overlays and parameters are documented /boot/overlays/README | |
| device_tree= |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment