-
-
Save MoritzBuetzer/6441d4045f989ef57aed915250bb4020 to your computer and use it in GitHub Desktop.
- platform: rest | |
resource: http://[DEVICE_IP]/ai?command=getDeviceStatus | |
name: 'V-Zug CookTopInduktion V6000' | |
authentication: digest | |
username: !secret vzug.username | |
password: !secret vzug.password | |
json_attributes: | |
- DeviceName | |
- Serial | |
- Inactive | |
- Status | |
- Program | |
- ProgramEnd | |
- platform: template | |
sensors: | |
vzug_cooktopinduktion_devicename: | |
friendly_name: 'V-Zug CookTopInduktion V6000 DeviceName' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'DeviceName') }}" | |
vzug_cooktopinduktion_serial: | |
friendly_name: 'V-Zug CookTopInduktion V6000 Serial' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'Serial') }}" | |
vzug_cooktopinduktion_inactive: | |
friendly_name: 'V-Zug CookTopInduktion V6000 Inactive' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'Inactive') }}" | |
vzug_cooktopinduktion_status: | |
friendly_name: 'V-Zug CookTopInduktion V6000 Status' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'Status') }}" | |
vzug_cooktopinduktion_program: | |
friendly_name: 'V-Zug CookTopInduktion V6000 Program' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'Program') }}" | |
vzug_cooktopinduktion_end: | |
friendly_name: 'V-Zug CookTopInduktion V6000 End' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'ProgramEnd')['End'] }}" | |
vzug_cooktopinduktion_endtype: | |
friendly_name: 'V-Zug CookTopInduktion V6000 End' | |
value_template: "{{ state_attr('sensor.v_zug_cooktopinduktion_v6000', 'ProgramEnd')['EndType'] }}" |
@Hensenen
I do not really use the integration in my dashboard but for push notifications if a program is finished. For this I simlply check on the sensor state and execute a notification.
platform: template value_template: "{{ 'Programm beendet' in states('sensor.v_zug_dishwasher') }}"
I use this integration for my "AdoraWaschen V2000" (the "dishwasher" and the "washer" have the same json attributes). But I often get the following error message:
{"error":{"code":503.01}}
The "unaesthetic" part is that the values are shown as unknown
but the bad thing is that this state change fills the log file. Anyone had the same problem? (Or an idea how to ignore those values)
I get the same error-code - always after finishing a programm. It started some months ago, so I guess it is connected with one of the latest updates. I contacted the VZUG support and got the following feedback:
Besten Dank für Ihre Interesse an der Vernetzung der V-ZUG Geräte. Momentan dient die Vernetzung unserer Geräte im Moment lediglich dem Zugriff auf die Geräte über die V-ZUG App sowie unseres Partners digitalStrom.
As mentioned in my post 3 weeks ago, they claim to work on an API update, which hopefully will solve this issue.
Hmm, thanks for the info. So we will wait for the next update...
Btw, any idea what the "EndType" is?
Hi There, does anybody know the correct json attributes for a combi steamer V6000? It looks that 'program' and 'status' is not working correctly, always got an empty string. Thanks in advance for any help!! JJ
Hmm, thanks for the info. So we will wait for the next update... Btw, any idea what the "EndType" is?
No, I am not sure. Just saw that while a program is running the value is "2" and as soon as the program stops it reports "0".
{"DeviceName":"","Serial":"XXX","Inactive":"false","Program":"Intensiv","Status":"Trocknen","ProgramEnd":{"End":"0h02","EndType":"2"},"deviceUuid":"XXX"}
and later
{"DeviceName":"","Serial":"XXX","Inactive":"false","Program":"Intensiv","Status":"Programm beendet, Nachtrocknen\nEnergie: 1,4 kWh, Wasser: 23 l","ProgramEnd":{"End":"","EndType":"0"},"deviceUuid":"XXX"}
Hi There, does anybody know the correct json attributes for a combi steamer V6000? It looks that 'program' and 'status' is not working correctly, always got an empty string. Thanks in advance for any help!! JJ
I don't have a V6000 so I cannot check the values, but have you tried the URL to get the status?
http://DEVICEIP/ai?command=getDeviceStatus
Hi There, does anybody know the correct json attributes for a combi steamer V6000? It looks that 'program' and 'status' is not working correctly, always got an empty string. Thanks in advance for any help!! JJ
I don't have a V6000 so I cannot check the values, but have you tried the URL to get the status?
http://DEVICEIP/ai?command=getDeviceStatus
Yes, I did it. But always get empty result for program and status, as below. Any ideas what might be wrong?
Thanks JJ
{"DeviceName":"","Serial":"23030 000000","Inactive":"false","Program":"","Status":"","ProgramEnd":{"EndType":"0","End":""},"deviceUuid":"3300600"}
Yes, in the mobile app status and program is shown properly.
And yes, I tested it also during running state e.q. inactive = false. Same result/effect -> no status nor program information.
Hi all, I just found this thread, owner of a V4000 dishwasher as well. In browsing around I found another thread where they managed to get a bit more data out of the vzug appliances.
I found the following:
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_ENERGY_PROGRAM&_=1673954407332
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_WATER_PROGRAM&_=1673954407333
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_ENERGY_AVG&_=1673954407334
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_WATER_AVG&_=1673954407335
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_ENERGY_TOTAL&_=1673954407337
http://172.16.0.xx/hh?command=getCommand&value=ECO_MGMT_WATER_TOTAL&_=1673954407338
Calling these gives me a json response:
{"type":"status","description":"Total consumption","command":"ECO_MGMT_ENERGY_TOTAL","value":"346 kWh","alterable":false}
Using this code I can get the value in HA:
- scan_interval: 300
resource: http://172.16.0.98/hh?command=getCommand&value=ECO_MGMT_ENERGY_TOTAL
sensor:
name: v_zug_totalenergy
json_attributes:
- command
- value
and
template:
- sensor:
- name: v_zug_dishwasher_totalenergy
state: "{{ state_attr('sensor.v_zug_totalenergy', 'value') }}"
Three issues:
- The value is a string, could someone help me learn how to convert it to an interger?
- From what I can tell, each value requires a separate REST call. Any idea how to "elegantly" put this into a config file?
- I think the number at the end of the URL is a unix timestamp
Hi,
looking into the same parameters - want to read out total (and if possible current) energy and water consumtion from my machines to feed it in the energy monitor.
Your issues:
- Yes most likely a unix epoch - however I learned that the API ignores values that are not implemented if added but you might play around and query historic values, if they change its a valid value parameter and the device stores historic states which would be nice.
My issues:
-
both are Adora V2000 series, both on latest firmware
-
I get an error {"error":{"code":400.03}}
-
this issue expands on commands:
/hh?command=getCommands
/hh?command=getCommand
/hh?command=doTurnOff -
some commands work such as:
/hh?command=getCategories
/hh?command=getProgram
/hh?command=getZHMode
/ai?command=getModelDescription
/hh?command=getCategory&value=EcoManagement
/ai?command=getDeviceStatus
/ai?command=getLastPUSHNotifications
Any ideas?
- The value is a string, could someone help me learn how to convert it to an interger?
Hi all
I have a V4000 since some days and I gave all of it a bit of additional love. Here's my current config:
rest:
- scan_interval: 20
resource: http://192.168.2.2/ai?command=getDeviceStatus
sensor:
name: vzug_dishwasher
json_attributes:
- DeviceName
- Serial
- Inactive
- Status
- Program
- ProgramEnd
- EndType
- scan_interval: 60
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_PROGRAM
sensor:
name: vzug_dishwasher_last_energy
value_template: "{{value_json.value[:-3].replace(',','.') | float(0) }}" # strip kWh
unit_of_measurement: "kWh"
- scan_interval: 120
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_AVG
sensor:
name: vzug_dishwasher_avg_energy
value_template: "{{ value_json.value[:-7].replace(',','.') | float(0) }}" # strip kWh/Ch.
unit_of_measurement: "kWh"
- scan_interval: 60
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_TOTAL
sensor:
name: vzug_dishwasher_tot_energy
value_template: "{{value_json.value[:-3].replace(',','.') | float(0) }}" # strip kWh
unit_of_measurement: "kWh"
- scan_interval: 60
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_PROGRAM
sensor:
name: vzug_dishwasher_last_water
value_template: "{{ value_json.value[:-1].replace(',','.') | float(0) }}" # strip l
unit_of_measurement: "l"
- scan_interval: 120
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_AVG
sensor:
name: vzug_dishwasher_avg_water
value_template: "{{ value_json.value[:-5].replace(',','.') | float(0) }}" # strip l/Ch.
unit_of_measurement: "l"
- scan_interval: 60
resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_TOTAL
sensor:
name: vzug_dishwasher_tot_water
value_template: "{{ value_json.value[:-1].replace(',','.') | float(0) }}" # strip l
unit_of_measurement: "l"
template:
- sensor:
- name: vzug_dishwasher_devicename
state: "{{ state_attr('sensor.vzug_dishwasher', 'DeviceName') }}"
- name: vzug_dishwasher_serial
state: "{{ state_attr('sensor.vzug_dishwasher', 'Serial') }}"
- name: vzug_dishwasher_inactive
state: "{{ state_attr('sensor.vzug_dishwasher', 'Inactive') }}"
- name: vzug_dishwasher_program
state: "{{ state_attr('sensor.vzug_dishwasher', 'Program') }}"
- name: vzug_dishwasher_status
state: "{{ state_attr('sensor.vzug_dishwasher', 'Status') }}"
- name: vzug_dishwasher_program_end
state: "{{ state_attr('sensor.vzug_dishwasher', 'ProgramEnd').End }}"
- name: vzug_dishwasher_program_end_type
state: "{{ state_attr('sensor.vzug_dishwasher', 'ProgramEnd').EndType }}"
hi guys I am a bit confused.
I should just be able to add a sensors.yaml with the last code from phoebos02
include it in the configuration and then it should work?
Or am I understanding this wrong?
- The value is a string, could someone help me learn how to convert it to an interger?
Hi all
I have a V4000 since some days and I gave all of it a bit of additional love. Here's my current config:
rest: - scan_interval: 20 resource: http://192.168.2.2/ai?command=getDeviceStatus sensor: name: vzug_dishwasher json_attributes: - DeviceName - Serial - Inactive - Status - Program - ProgramEnd - EndType - scan_interval: 60 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_PROGRAM sensor: name: vzug_dishwasher_last_energy value_template: "{{value_json.value[:-3].replace(',','.') | float(0) }}" # strip kWh unit_of_measurement: "kWh" - scan_interval: 120 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_AVG sensor: name: vzug_dishwasher_avg_energy value_template: "{{ value_json.value[:-7].replace(',','.') | float(0) }}" # strip kWh/Ch. unit_of_measurement: "kWh" - scan_interval: 60 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_ENERGY_TOTAL sensor: name: vzug_dishwasher_tot_energy value_template: "{{value_json.value[:-3].replace(',','.') | float(0) }}" # strip kWh unit_of_measurement: "kWh" - scan_interval: 60 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_PROGRAM sensor: name: vzug_dishwasher_last_water value_template: "{{ value_json.value[:-1].replace(',','.') | float(0) }}" # strip l unit_of_measurement: "l" - scan_interval: 120 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_AVG sensor: name: vzug_dishwasher_avg_water value_template: "{{ value_json.value[:-5].replace(',','.') | float(0) }}" # strip l/Ch. unit_of_measurement: "l" - scan_interval: 60 resource: http://192.168.2.2/hh?command=getCommand&value=ECO_MGMT_WATER_TOTAL sensor: name: vzug_dishwasher_tot_water value_template: "{{ value_json.value[:-1].replace(',','.') | float(0) }}" # strip l unit_of_measurement: "l" template: - sensor: - name: vzug_dishwasher_devicename state: "{{ state_attr('sensor.vzug_dishwasher', 'DeviceName') }}" - name: vzug_dishwasher_serial state: "{{ state_attr('sensor.vzug_dishwasher', 'Serial') }}" - name: vzug_dishwasher_inactive state: "{{ state_attr('sensor.vzug_dishwasher', 'Inactive') }}" - name: vzug_dishwasher_program state: "{{ state_attr('sensor.vzug_dishwasher', 'Program') }}" - name: vzug_dishwasher_status state: "{{ state_attr('sensor.vzug_dishwasher', 'Status') }}" - name: vzug_dishwasher_program_end state: "{{ state_attr('sensor.vzug_dishwasher', 'ProgramEnd').End }}" - name: vzug_dishwasher_program_end_type state: "{{ state_attr('sensor.vzug_dishwasher', 'ProgramEnd').EndType }}"
forgot to qoute
I also tried
rest:
- scan_interval: 600
resource: http://192.168.1.111/ai?command=getDeviceStatus
sensor:
name: v_zug_oven
json_attributes:
- DeviceName
- Serial
- Inactive
- Status
- Program
- ProgramEnd - resource: http://192.168.1.111/report
template:
- sensor:
- name: oven_name
state: "{{ state_attr('sensor.v_zug_oven', 'DeviceName') }}"
- name: oven_name
- sensor:
- name: oven_inactive
state: "{{ state_attr('sensor.v_zug_oven', 'Inactive') }}"
- name: oven_inactive
- sensor:
- name: oven_status
state: "{{ state_attr('sensor.v_zug_oven', 'Status') }}"
- name: oven_status
- sensor:
- name: oven_program
state: "{{ state_attr('sensor.v_zug_oven', 'Program') }}"
- name: oven_program
- sensor:
- name: oven_program_end
state: "{{ state_attr('sensor.v_zug_oven', 'ProgramEnd') }}"
- name: oven_program_end
I'm not sure if this is still useful to anyone, but if I've noticed that the web UI always calls http://<ip>/hh?command=getZHMode
right before calling http://<ip>/ai?command=getDeviceStatus
.
If I do the same, then the amount of 501.03
errors is significantly reduced.
@izacus How can I combine this "wakeup" call with the rest call?
hi
i use the following config to get the engergy statistics:
sensor:
- platform: rest
name: 'V-Zug AdoraWash V4000 Eco Info'
json_attributes_path: "$.energy"
json_attributes:
- total
- lastMonth
- lastYear
- average
- program
resource: http://192.168.2.xx/hh?command=getEcoInfo
template:
- sensor:
- name: "V-Zug AdoraWash Energy total"
device_class: energy
state_class: total_increasing
unit_of_measurement: kWh
state: >
{{ state_attr('sensor.v_zug_adorawash_v4000_eco_info', 'total')}}
- name: "V-Zug AdoraWash Energy total"
That works with my adora wash v4000, AdoraDish V4000, Combair and Combisteamer v6000
but v-zug will change their api in the future. they will publish the new api.
but v-zug will change their api in the future. they will publish the new api.
Hello @asowlnowl, is there a way to know more about this new API effort? Do you have a contact with v-zug?
Hello @asowlnowl, is there a way to know more about this new API effort? Do you have a contact with v-zug?
they told me last fall that they have no eta yet. i just asked per contact form on their website for the api documentation.
FYI, I finally bit the bullet and created a proper integration for Home Assistant that can be installed using HACS.
The integration can be found here: https://github.com/siku2/hass-vzug
I used a lot of information in this thread for reference, so thank you all for sharing.
Nice one! Can’t wait to try it out. 👍
Thank you for this - only had basic date before now a lot more is in the HACS integration. Great stuff!
@siku2 awesome!
Awsome, Thanks
I have a AdoraDish V2000 I get the error "Einrichtung fehlgeschlage, wird erneut versucht" I guess the interface is not compatible with the V4000....
@simondaehler, can you create a new issue or discussion over at the repository? I would like to figure out what the issue is so the V2000 series can be supported as well, I just need a few things from your side and I don't want to clog up this thread.
@siku2 I'm using your integration with an adorawash_v2000. I set it up with the very first version, so at least this one did work.
I have both adorawash2000 and adoradry2000 and it works with latest version 0.31. Thanks a lot
@daphil012
Alright, thanks so far guys :) i managed to integrate the vzug Adora V4000 with these variables. I already made some quick n dirty card by using a combination of vertical/horizontal card with entitys, which works fine generally - but i have a problem with the remaining time (Programend).
As you can see in the screenshot, i get the whole string incl. the endtype - but i only would like to see the tie itself, without the other marks.
Since you seem to have a similiar dishwasher, do you get this string too - or how did you manage that point?
Another thing: which kind of config/card did you use for your integration? i guess there are many better options, but couldnt find anything specific in my short google search.