Created
November 3, 2021 21:33
-
-
Save JettScythe/64a367ca8c7a350924215e33b1abc2a6 to your computer and use it in GitHub Desktop.
EDITED Nov.3rd 2021
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[stepper_x] | |
step_pin: PB13 | |
dir_pin: !PB12 | |
enable_pin: !PB14 | |
microsteps: 16 | |
rotation_distance: 40 | |
endstop_pin: tmc2209_stepper_x:virtual_endstop | |
homing_retract_dist: 0 | |
position_endstop: 0 | |
position_max: 235 | |
homing_speed: 20 | |
[tmc2209 stepper_x] | |
uart_pin: PC11 | |
tx_pin: PC10 | |
uart_address: 0 | |
run_current: 0.580 | |
diag_pin: ^PC0 | |
driver_SGTHRS: 55 | |
stealthchop_threshold: 999999 | |
[stepper_y] | |
step_pin: PB10 | |
dir_pin: !PB2 | |
enable_pin: !PB11 | |
microsteps: 16 | |
rotation_distance: 40 | |
endstop_pin: tmc2209_stepper_y:virtual_endstop | |
homing_retract_dist: 0 | |
position_endstop: 0 | |
position_max: 235 | |
position_min: -1.5 | |
homing_speed: 20 | |
[tmc2209 stepper_y] | |
uart_pin: PC11 | |
tx_pin: PC10 | |
uart_address: 2 | |
run_current: 0.580 | |
diag_pin: ^PC1 | |
driver_SGTHRS: 55 | |
stealthchop_threshold: 999999 | |
[stepper_z] | |
step_pin: PB0 | |
dir_pin: PC5 | |
enable_pin: !PB1 | |
microsteps: 16 | |
rotation_distance: 8 | |
endstop_pin: probe:z_virtual_endstop | |
position_min: -3 | |
position_max: 250 | |
[tmc2209 stepper_z] | |
uart_pin: PC11 | |
tx_pin: PC10 | |
uart_address: 1 | |
run_current: 0.580 | |
hold_current: 0.500 | |
[extruder] | |
max_extrude_only_distance: 100.0 | |
step_pin: PB3 | |
dir_pin: !PB4 | |
enable_pin: !PD2 | |
microsteps: 16 | |
rotation_distance: 24.474 | |
nozzle_diameter: 0.400 | |
filament_diameter: 1.750 | |
heater_pin: PC8 | |
sensor_type: EPCOS 100K B57560G104F | |
sensor_pin: PA0 | |
min_temp: 0 | |
max_temp: 250 | |
[tmc2209 extruder] | |
uart_pin: PC11 | |
tx_pin: PC10 | |
uart_address: 3 | |
run_current: 0.650 | |
hold_current: 0.500 | |
stealthchop_threshold: 999999 | |
[heater_bed] | |
heater_pin: PC9 | |
sensor_type: EPCOS 100K B57560G104F | |
sensor_pin: PC3 | |
min_temp: 0 | |
max_temp: 130 | |
[heater_fan nozzle_cooling_fan] | |
pin: PC7 | |
[fan] | |
pin: PC6 | |
[mcu] | |
serial: /dev/ttyAMA0 | |
baud: 250000 | |
restart_method: command | |
[printer] | |
kinematics: cartesian | |
max_velocity: 300 | |
max_accel: 3000 | |
max_z_velocity: 5 | |
max_z_accel: 100 | |
[output_pin beeper] | |
pin: EXP1_1 | |
[static_digital_output usb_pullup_enable] | |
pins: !PA14 | |
[virtual_sdcard] | |
path: ~/.octoprint/uploads/ | |
[bltouch] | |
stow_on_each_sample: False | |
probe_with_touch_mode: False | |
sensor_pin: ^PC14 | |
control_pin: PA1 | |
samples: 1 | |
x_offset: -50.5 | |
y_offset: -6.5 | |
#z_offset: 0.0 | |
[safe_z_home] | |
home_xy_position: 117.5,117.5 | |
z_hop: 10 | |
z_hop_speed: 10 | |
[bed_mesh] | |
speed: 60 | |
horizontal_move_z: 5 | |
mesh_min: 25,25 | |
mesh_max: 188, 212 | |
probe_count: 3 | |
fade_start: 1 | |
fade_end: 10 | |
fade_target: 0 | |
[board_pins] | |
aliases: | |
# EXP1 header | |
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>, | |
EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB15, EXP1_10=<5V> | |
#*# <---------------------- SAVE_CONFIG ----------------------> | |
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. | |
#*# | |
#*# [extruder] | |
#*# control = pid | |
#*# pid_kp = 28.960 | |
#*# pid_ki = 2.011 | |
#*# pid_kd = 104.256 | |
#*# | |
#*# [heater_bed] | |
#*# control = pid | |
#*# pid_kp = 73.916 | |
#*# pid_ki = 1.493 | |
#*# pid_kd = 914.715 | |
#*# | |
#*# [bltouch] | |
#*# z_offset = 1.3 | |
#*# | |
#*# [bed_mesh default] | |
#*# version = 1 | |
#*# points = | |
#*# -0.025000, 0.030000, 0.045000 | |
#*# 0.047500, 0.030000, 0.020000 | |
#*# 0.115000, 0.082500, 0.077500 | |
#*# tension = 0.2 | |
#*# min_x = 25.0 | |
#*# algo = lagrange | |
#*# y_count = 3 | |
#*# mesh_y_pps = 2 | |
#*# min_y = 25.0 | |
#*# x_count = 3 | |
#*# max_y = 212.0 | |
#*# mesh_x_pps = 2 | |
#*# max_x = 188.0 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment