Last active
July 26, 2016 19:22
-
-
Save Jaesin/7a04e38591c95774d75d9107b5416ca5 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[profile] | |
layer_height = 0.2 | |
wall_thickness = 0.7 | |
retraction_enable = True | |
solid_layer_thickness = .6 | |
fill_density = 100 | |
print_speed = 60 | |
print_temperature = 187 | |
print_temperature2 = 200 | |
print_temperature3 = 0 | |
print_temperature4 = 0 | |
print_temperature5 = 0 | |
print_bed_temperature = 70 | |
support = Touching buildplate | |
platform_adhesion = Brim | |
support_dual_extrusion = Both | |
wipe_tower = False | |
wipe_tower_volume = 15 | |
ooze_shield = False | |
filament_diameter = 1.75 | |
filament_diameter2 = 1.75 | |
filament_diameter3 = 0 | |
filament_diameter4 = 0 | |
filament_diameter5 = 0 | |
filament_flow = 100 | |
nozzle_size = 0.35 | |
retraction_speed = 40.0 | |
retraction_amount = 5 | |
retraction_dual_amount = 16 | |
retraction_min_travel = 2 | |
retraction_combing = All | |
retraction_minimal_extrusion = 0.02 | |
retraction_hop = 0.1 | |
bottom_thickness = 0.25 | |
layer0_width_factor = 100 | |
object_sink = 0.0 | |
overlap_dual = 0.15 | |
travel_speed = 140.0 | |
bottom_layer_speed = 30 | |
infill_speed = 80 | |
solidarea_speed = 30 | |
inset0_speed = 50 | |
insetx_speed = 80 | |
cool_min_layer_time = 5 | |
fan_enabled = False | |
skirt_line_count = 1 | |
skirt_gap = 3.0 | |
skirt_minimal_length = 150.0 | |
fan_full_height = 0.5 | |
fan_speed = 40 | |
fan_speed_max = 50 | |
cool_min_feedrate = 10 | |
cool_head_lift = False | |
solid_top = True | |
solid_bottom = True | |
fill_overlap = 15 | |
perimeter_before_infill = True | |
support_type = Lines | |
support_angle = 45 | |
support_fill_rate = 15 | |
support_xy_distance = 0.7 | |
support_z_distance = 0.15 | |
spiralize = False | |
simple_mode = False | |
brim_line_count = 16 | |
raft_margin = 5.0 | |
raft_line_spacing = 3.0 | |
raft_base_thickness = 0.3 | |
raft_base_linewidth = 1.0 | |
raft_interface_thickness = 0.27 | |
raft_interface_linewidth = 0.4 | |
raft_airgap_all = 0.0 | |
raft_airgap = 0.22 | |
raft_surface_layers = 2 | |
raft_surface_thickness = 0.27 | |
raft_surface_linewidth = 0.4 | |
fix_horrible_union_all_type_a = True | |
fix_horrible_union_all_type_b = False | |
fix_horrible_use_open_bits = False | |
fix_horrible_extensive_stitching = False | |
plugin_config = | |
object_center_x = -1 | |
object_center_y = -1 | |
[alterations] | |
start.gcode = ; M140 S{print_bed_temperature} ;set bed temperature, no wait | |
M104 T0 S{print_temperature} ;set EX0 temperature, no wait | |
; M104 T1 S{print_temperature2} ;set EX1 temperature, no wait | |
;set temps again and wait | |
; M190 S{print_bed_temperature} ;set bed temp and wait | |
M109 T0 S{print_temperature} ;set EX0 temp and wait | |
; M109 T1 S{print_temperature2} ;set EX1 temp and wait | |
G17 ;set plane to XY (not really necessary...) | |
G21 ;set units to mm (or G20 for inches) | |
G90 ;set to absolute positioning (or G91 for incremental/relative) | |
M82 ;set extruder to absolute mode (or M83 for relative) | |
M107 ;fan off | |
M203 X10000 Y10000 Z600 E250 ;set max feedrates | |
G28 ;home all Axes | |
;G1 Z15.0 F(travel_speed) | |
;T1 ;Switch to the 2nd extruder | |
;G92 E0 ;zero the extruded length | |
;G1 F200 E10 ;extrude 10mm of feed stock | |
;G92 E0 ;zero the extruded length again | |
;G1 F200 E-{retraction_dual_amount} | |
T0 ;switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F600 Z0.2 ;prepare for extruder prime manuver | |
G1 F1200 X100 Y0 E8 ;extrude 20mm of feed stock | |
G1 F1200 Y0.5 | |
G1 F1200 X0 Y0.5 E16 | |
G1 F15000 X0 Y10 ;wipe the print head | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
end.gcode = | |
M104 T0 S0 ;extruder heater off | |
;M104 T1 S0 ;extruder heater off | |
;M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G90 | |
G00 X75 Y140 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
;G90 ;absolute positioning | |
;{profile_string} | |
start2.gcode = | |
M140 S{print_bed_temperature} ;set bed temperature, no wait | |
M104 T0 S{print_temperature} ;set EX0 temperature, no wait | |
M104 T1 S{print_temperature2} ;set EX1 temperature, no wait | |
;set temps again and wait | |
M190 S{print_bed_temperature} ;set bed temp and wait | |
M109 T0 S{print_temperature} ;set EX0 temp and wait | |
M109 T1 S{print_temperature2} ;set EX1 temp and wait | |
G17 ;set plane to XY (not really necessary...) | |
G21 ;set units to mm (or G20 for inches) | |
G90 ;set to absolute positioning (or G91 for incremental/relative) | |
M82 ;set extruder to absolute mode (or M83 for relative) | |
M107 ;fan off | |
M203 X10000 Y10000 Z600 E250 ;set max feedrates | |
G28 ;home all Axes | |
G1 Z15.0 F(travel_speed) | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
end2.gcode = | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G90 | |
G00 X75 Y140 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
;G90 ;absolute positioning | |
;{profile_string} | |
start3.gcode = | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T2 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end3.gcode = | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M104 T2 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
;{profile_string} | |
start4.gcode = | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T3 ;Switch to the 4th extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T2 ;Switch to the 3th extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end4.gcode = | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M104 T2 S0 ;extruder heater off | |
M104 T3 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
;{profile_string} | |
support_start.gcode = | |
support_end.gcode = | |
cool_start.gcode = | |
cool_end.gcode = | |
replace.csv = | |
preswitchextruder.gcode = | |
;This code is added before the T(n) | |
postswitchextruder.gcode = | |
;This code is added after the T(n) | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment